ابزار عیب‌یابی گوشی

مطمئن نیستید سخت‌افزارتان مشکل دارد؟ این بررسی‌های گام‌به‌گام را با کدهای عیب‌یابی داخلی گوشی اجرا کنید.

بررسی لمس، صفحه و حسگرها

این‌ها بررسی‌های راهنما روی گوشی هستند، نه اندازه‌گیری مرورگر یا تشخیص تعمیر. خواندن آن‌ها به پرداخت یا دانلود نیاز ندارد.

تست لمس

صفحه را تمیز و خشک کنید، شارژر را جدا و محافظ آسیب‌دیده را بردارید. در برنامه نقاشی، خطوط پیوسته در مرکز و همه لبه‌ها بکشید. شکاف یا علامت ناخواسته ممکن است مشکل لمس باشد؛ پس از راه‌اندازی مجدد تکرار کنید. اگر منو شبکه لمس دارد، دستورهای آن را دنبال کنید.

تست صفحه

تصاویر یکدست قرمز، سبز، آبی، سفید و سیاه را با روشنایی متوسط ببینید. پیکسل مرده، تغییر رنگ و سوسوزدن را بررسی کنید. با نمایشگر دیگری مقایسه کنید: تصویر صفحه خرابی فیزیکی پنل را نشان نمی‌دهد. به پنل فشار ندهید.

تست حسگر

چرخش خودکار را در برنامه سازگار بررسی کنید. هنگام تماس معمولی، ناحیه حسگر مجاورت را بپوشانید و باز کنید؛ خاموش و روشن شدن صفحه را ببینید. قاب یا محافظ ممکن است تداخل ایجاد کند. تست حسگر را فقط در صورت وجود در مدل اجرا کنید؛ این بررسی‌ها سلامت همه حسگرها را ثابت نمی‌کنند.

فهرست کدهای تست بر اساس برند

Display & Touchscreen

Verify screen colour uniformity, dead pixels, and touch responsiveness across the whole panel.

*#0*#
1. Dial the code to open the built-in test menu.\n2. Cycle Red, Green, Blue and White screens — look for dead or stuck pixels.\n3. Run the touch test and draw across every edge to confirm digitizer response.

Battery Health

Check current battery voltage, temperature and charging behaviour.

*#*#4636#*#*
1. Dial the code and open Battery information.\n2. Note the current charge, temperature and health status.\n3. Compare voltage under load vs idle to spot a degrading cell.

Network & Signal

Inspect signal strength, cell ID and neighbouring towers.

*3001#12345#* (iOS) / *#*#4636#*#* (Android)
1. Dial the code for your platform.\n2. Read the signal in dBm — closer to 0 is stronger.\n3. Note cell ID and PLMN for troubleshooting weak-signal areas.

Sensors

Test accelerometer, gyroscope, proximity and light sensors.

*#0*#
1. Open the test menu.\n2. Select Sensors and verify each sensor reacts to motion, light, or covering the proximity area.\n3. Fail any sensor that does not update.

Speaker & Vibration

Confirm the earpiece, loudspeaker and vibration motor all fire.

*#*#0842#*#*
1. Run the vibration test — the phone should pulse.\n2. Run the melody / speaker test and listen for distortion.\n3. Place a call to verify the earpiece.

Camera

Trigger front and rear cameras through the diagnostic menu to spot lens or sensor failures.

*#0*#
1. Open the built-in test menu.\n2. Launch front and rear camera tests.\n3. Look for stuck pixels, discolouration, or autofocus failures.

GPS

Verify GPS satellite lock and location fix accuracy.

*#*#1472365#*#*
1. Dial the code and start the GPS test.\n2. Move outdoors and wait up to 60 seconds for a fix.\n3. Confirm satellites in view and accuracy in metres.